N-(3-hydroxypropyl)prop-2-enamide

反応条件: temp:0.00; pressure:0.00; stir:; See reaction.notes.procedure_details.

実験手順: To a 250 mL, four-neck round bottom flask equipped with a mechanical stirrer, a thermometer, a 100 mL dropping fuel, and a nitrogen inlet/outlet, 30.0 g of 1-amino-3-propanol (0.4 mole), and 100 mL of acetonitrile were added. The mixture was cooled below 0° C. with an ice/water bath. To this solution, 18.1 g of freshly distilled acryloyl chloride (0.2 mole) in 50 mL of acetonitrile was added through the dropping funnel. The addition rate was controlled so that the reaction temperature was kept below 0° C. After the addition was finished and the agitation was turned off, the reaction solution separated into two liquid phases. The bottom layer viscous salt solution phase was discarded. 100 mL of deionized water was added to the top layer acetonitrile solution phase. After removing all acetonitrile by vacuum distillation, the aqueous solution was passed through a mixed bed ion-exchange column packed with 20 g of Dowex MR-3C resin. A total of 76 grams of eluate was collected. The final solution has the following properties: HPLC and FT-IR analysis indicates there is no ester formation; HPAA concentration: 7.2% (wt/wt); pH=5.6 at 25° C.; Conductivity=56.6 μS/cm at 25° C.; Viscosity=1.1 cPs at 25° C. The relative low yield of HPAA is due to the fact that HPAA is soluble in the salt phase. HPAA in the salt phase can be recovered by acetone extraction since HPAA is soluble in acetone, and the salt is insoluble. To a 250 mL, four-neck round bottom flask equipped with a mechanical stirrer were added The mixture was cooled below 0° C. with an ice/water bath was kept below 0° C After the addition the reaction solution separated into two liquid phases 100 mL of deionized water was added to the top layer acetonitrile solution phase After removing all acetonitrile by vacuum distillation A total of 76 grams of eluate was collected at 25° C. at 25° C. at 25° C HPAA in the salt phase can be recovered by acetone extraction since HPAA

反応条件: temp:0.00; pressure:0.00; stir:; See reaction.notes.procedure_details.

実験手順: To a 250 mL, four-neck round bottom flask equipped with a mechanical stirrer, a thermometer, a 100 mL dropping fuel, and a nitrogen inlet/outlet, 30.0 g of 1-amino-3-propanol (0.4 mole), and 100 mL of acetonitrile were added. The mixture was cooled below 0° C. with an ice/water bath. To this solution, 18.1 g of freshly distilled acryloyl chloride (0.2 mole) in 50 mL of acetonitrile was added through the dropping funnel. The addition rate was controlled so that the reaction temperature was kept below 0° C. After the addition was finished and the agitation was turned off, the reaction solution separated into two liquid phases. The bottom layer viscous salt solution phase was discarded. 100 mL of deionized water was added to the top layer acetonitrile solution phase. After removing all acetonitrile by vacuum distillation, the aqueous solution was passed through a mixed bed ion-exchange column packed with 20 g of Dowex MR-3C resin. A total of 76 grams of eluate was collected. The final solution has the following properties: HPLC and FT-IR analysis indicates there is no ester formation; HPAA concentration: 7.2% (wt/wt); pH=5.6 at 25° C.; Conductivity=56.6 μS/cm at 25° C.; Viscosity=1.1 cPs at 25° C. The relative low yield of HPAA is due to the fact that HPAA is soluble in the salt phase. HPAA in the salt phase can be recovered by acetone extraction since HPAA is soluble in acetone, and the salt is insoluble. To a 250 mL, four-neck round bottom flask equipped with a mechanical stirrer were added The mixture was cooled below 0° C. with an ice/water bath was kept below 0° C After the addition the reaction solution separated into two liquid phases 100 mL of deionized water was added to the top layer acetonitrile solution phase After removing all acetonitrile by vacuum distillation A total of 76 grams of eluate was collected at 25° C. at 25° C. at 25° C HPAA in the salt phase can be recovered by acetone extraction since HPAA

反応条件: temp:0.00; pressure:0.00; stir:; See reaction.notes.procedure_details.

実験手順: To a 250 mL, four-neck round bottom flask equipped with a mechanical stirrer, a thermometer, a 100 mL dropping funnel, and a nitrogen inlet/outlet, 30.0 g of 1-amino-3-propanol (0.4 mole), and 100 mL of acetonitrile were added. The mixture was cooled below 0° C. with an ice/water bath. To this solution, 18.1 g of freshly distilled acryloyl chloride (0.2 mole) in 50 mL of acetonitrile was added through the dropping funnel. The addition rate was controlled so that the reaction temperature was kept below 0° C. After the addition was finished and the agitation was turned off, the reaction solution separated into two liquid phases. The bottom layer viscous salt solution phase was discarded. To the top layer acetonitrile solution phase, 100 mL of deionized water was added. After removing all acetonitrile by vacuum distillation, the aqueous solution was passed through a mixed bed ion-exchange column packed with 20 g of Dowex MR-3C resin. A total of 76 grams of eluate was collected. The final solution has the following properties: HPLC and FT-IR analysis indicates there is no ester formation; HPAA concentration: 7.2% (wt/wt); pH=5.6 at 25° C; Conductivity=56.6 μS/cm at 25° C.; Viscosity=1.1 cPs at 25° C. The relative low yield of HPAA is due to the fact that HPAA is soluble in the salt phase. HPAA in the salt phase can be recovered by acetone extraction since HPAA is soluble in acetone, and the salt is insoluble. To a 250 mL, four-neck round bottom flask equipped with a mechanical stirrer The mixture was cooled below 0° C. with an ice/water bath was kept below 0° C After the addition the reaction solution separated into two liquid phases To the top layer acetonitrile solution phase, 100 mL of deionized water was added After removing all acetonitrile by vacuum distillation A total of 76 grams of eluate was collected at 25° C at 25° C. at 25° C HPAA in the salt phase can be recovered by acetone extraction since HPAA

反応条件: temp:0.00; pressure:0.00; stir:; See reaction.notes.procedure_details.

実験手順: To a 250 mL, four-neck round bottom flask equipped with a mechanical stirrer, a thermometer, a 100 mL dropping fuel, and a nitrogen inlet/outlet, 30.0 g of 1-amino-3-propanol (0.4 mole), and 100 mL of acetonitrile were added. The mixture was cooled below 0° C. with an ice/water bath. To this solution, 18.1 g of freshly distilled acryloyl chloride (0.2 mole) in 50 mL of acetonitrile was added through the dropping funnel. The addition rate was controlled so that the reaction temperature was kept below 0° C. After the addition was finished and the agitation was turned off, the reaction solution separated into two liquid phases. The bottom layer viscous salt solution phase was discarded. 100 mL of deionized water was added to the top layer acetonitrile solution phase. After removing all acetonitrile by vacuum distillation, the aqueous solution was passed through a mixed bed ion-exchange column packed with 20 g of Dowex MR-3C resin. A total of 76 grams of eluate was collected. The final solution has the following properties: HPLC and FT-IR analysis indicates there is no ester formation; HPAA concentration: 7.2% (wt/wt); pH=5.6 at 25° C.; Conductivity=56.6 μS/cm at 25° C.; Viscosity=1.1 cPs at 25° C. The relative low yield of HPAA is due to the fact that HPAA is soluble in the salt phase. HPAA in the salt phase can be recovered by acetone extraction since HPAA is soluble in acetone, and the salt is insoluble. To a 250 mL, four-neck round bottom flask equipped with a mechanical stirrer were added The mixture was cooled below 0° C. with an ice/water bath was kept below 0° C After the addition the reaction solution separated into two liquid phases 100 mL of deionized water was added to the top layer acetonitrile solution phase After removing all acetonitrile by vacuum distillation A total of 76 grams of eluate was collected at 25° C. at 25° C. at 25° C HPAA in the salt phase can be recovered by acetone extraction since HPAA