1-ethenoxy-2-(2-ethenoxyethoxy)ethane

反応条件: temp:0.00; pressure:0.00; stir:; See reaction.notes.procedure_details.

実験手順: In the following examples, cyclohexyl vinyl ether (CHVE), 2-ethylhexyl vinyl ether (EHVE), diethyleneglycol divinyl ether (DGDVE) and 9-anthracenemethanol were obtained from Aldrich Chemical Company. 1,4-butanediol divinyl ether (BDVE), trimethyleneglycol trivinyl ether (TMPVE), cyclohexanedimethanol divinyl ether (CHDVE) and nonanediol divinyl ether (NDVE) were obtained from Nippon Carbide Industries, Co. Inc. 1,3-benzenedimethyl divinyl ether (BDMDVE) was synthesized from 1,3-benzenedimethanol, which was prepared in a two-liter, 3-necked round-bottomed flask equipped with a 500-ml constant pressure addition funnel, an overhead stirrer, a thermocouple and a nitrogen inlet into which was added 27 g (0.74 mol) of lithium aluminum hydride (95%) and 1000 ml of anhydrous tetrahydrofuran (THF). The addition funnel was charged with a solution of 100 g (0.493 mol) of isophthaloyl dichloride in 400 ml of anhydrous THF. Diacylchloride was added slowly over a period of 2 hours with cooling in an ice bath. Once addition was complete the ice bath was removed and the suspension allowed to reach room temperature for four hours at which time it was re-cooled and 200 ml of ethyl acetate was slowly added to decompose the remaining hydride. The addition funnel was recharged with 200 ml of 2M NaOH, which was then added slowly with vigorous stirring until the ensuing suspension became granular in appearance. The suspension was filtered and well washed with ethyl acetate. The combined filtrate and washings were then washed with brine, dried over anhydrous magnesium sulfate and evaporated on a rotary evaporator to yield 64 g (94%) of 1,3-benzenedimethanol as a clear, colorless oil which solidified upon standing. The BDMDVE was then prepared in a two-liter round bottomed flask equipped with a positive-pressure nitrogen inlet and a magnetic stir bar was added 64 g (0.46 mol) of 1,3-benzenedimethanol, 10 g (0.03 mol) of mercuric acetate and 1 liter of ethyl vinyl ether. The solution was stirred at room temperature for four days at which time it was washed well with saturated sodium bicarbonate solution and brine. The solution was then stirred for three days over 20 g of anhydrous magnesium sulfate (the reaction is driven to completion by stirring over the acidic magnesium sulfate), filtered, and evaporated on a rotary evaporator. The resulting oil was distilled twice through an 8″ Vigreux to yield 53 g (60%) of BDMDVE, boiling point=84° C. at 1 mm Hg. was prepared in a two-liter, 3-necked round-bottomed flask equipped with a 500-ml constant pressure addition funnel, an overhead stirrer with cooling in an ice bath Once addition was removed was re-cooled 200 ml of ethyl acetate was slowly added was then added slowly The suspension was filtered well washed with ethyl acetate The combined filtrate and washings were then washed with brine dried over anhydrous magnesium sulfate evaporated on a rotary evaporator

反応条件: temp:50.01; pressure:0.00; stir:; See reaction.notes.procedure_details.

実験手順: Sodium chloride (116 g), 4 drops concentrated sulfuric acid and 150 g of water are added to a 1-liter flask containing an efficient two-tiered stirrer, condenser, and nitrogen inlet tube. Polyacrylic acid dispersant, such as 5 gm of Primafloc C-7 available from Rohm and Haas Company, is then added to a solution containing a 0.1 g tannic acid dissolved in 136 g of water. This solution is then added to the stirred flask containing sodium chloride. This aqueous phase is then sparged with nitrogen. In a separate flask, 314 mls. of acrolein is sparged for 20 - 30 minutes with nitrogen. In a separate flask a solution of 29.6 g of divinylbenzene (DVB-81.1% active), 6.0 g of diethyleneglycoldivinylether (DEGDVE), and 9.0 g of Percadox 16 (bis-t-butylcyclohexyl percarbonate) is prepared. This latter solution is then added to acrolein, shaken until homogeneous, and added to the aqueous phase in the reaction flask after the stirrer had been turned off and the nitrogen sparge had been converted to a nitrogen atmosphere. A suspension formed in 20 - 30 minutes on intermittent agitation at 145 rpm. The position of the stirrer blade must be at the interfaces of the two liquid phases. After the dispersion is formed, the reaction mixture is heated to 50°C. and held there with intermittent heating and air cooling for 16 hours. The reaction contents are then cooled to room temperature, the liquid drained, and the resin given three water washes. After washing with methanol, the resin is dried at 75°C. for 16 hours. containing an efficient two-tiered stirrer, condenser, and nitrogen inlet tube This solution is then added to the stirred flask This aqueous phase is then sparged with nitrogen of acrolein is sparged for 20 - 30 minutes with nitrogen added to the aqueous phase in the reaction flask after the stirrer the nitrogen sparge A suspension formed in 20 - 30 minutes on intermittent agitation at 145 rpm After the dispersion is formed with intermittent heating air cooling for 16 hours The reaction contents are then cooled to room temperature After washing with methanol the resin is dried at 75°C. for 16 hours